Guides · Marmi di Carrara · 1956
Grout lines and joints in a marble floor
Updated · By Marmi di Carrara srl
What it looks like
Joint problems show before marble problems. A dirty joint is a grey or dark line between clean tiles, most visible in kitchens and corridors. A cracked joint shows a fissure along its centre or grout pulling away from the stone edges, leaving a gap where water gets in. A joint that crumbles under a fingernail indicates a weak or badly applied grout. Joints opening all in the same direction, or a tile that sounds hollow, speak of the screed below, not of the grout. On light polished marbles, a dark halo along the tile edges is often a stain left by coloured or epoxy grout during installation.
What causes it
Marble is laid with narrow joints, 1-3 mm, because the tiles are calibrated and rectified: the joint absorbs small size variations and movements of the substrate. Cement grout is more porous than marble and holds dirt and grease; being a different material, it also moves differently with temperature and humidity. A new screed shrinks as it dries, slabs flex, underfloor heating expands and contracts: without flexible joints roughly every 20-25 m² and along the walls, the stress is released on the joints and then on the tiles. Finally, marble is calcium carbonate sensitive to acids: many "grout cleaners" are acidic and, while they whiten the grout, they dull the edges of the stone.
What to do at once and what not to do
For dirty joints use a slightly more concentrated pH-neutral detergent, let it work for a few minutes, run a soft-bristle brush along the joint and rinse with clean water; dry so as not to leave halos on the marble. For a cracked joint, observe first: if it is a single one and the floor does not move, the old grout can be scraped out and the joint regrouted by hand with a fine product of the same colour. Do not use acids, prolonged bleach, high-pressure steam or metal brushes. Do not fill joints with generic silicone: it yellows and stains. Do not grout a light polished marble with epoxy without prior protection and experience: the residue stays as a film that only re-polishing removes.
How to prevent it
Much is decided at installation. Agree with the installer on the joint width, 2 mm is a good size for most formats, and a fine grout in a colour similar to the marble background, not to the vein. In large floors, above 20-25 m² or with underfloor heating, ask for flexible expansion joints and a perimeter joint hidden under the skirting. On light polished marbles, a protective treatment before grouting prevents the grout from staining the edges. After installation, a water- and oil-repellent protective treatment also on the joints slows down soiling. In daily cleaning, little detergent and clean water: detergent residue is the first reason joints turn grey.
When to call us or a restorer
If several joints open together, if a tile lifts or sounds hollow, if cracks appear that cross grout and stone, the problem is in the screed or in missing expansion joints: you need an experienced installer, not a tube of grout. The same applies if the joints were grouted in the wrong colour or with epoxy that stained the polish: removal requires professional re-polishing. Our workshop in Carrara cuts replacement tiles in the same material when some pieces need replacing, with slabs in stock to match colour and vein, and can advise you and your installer on widths, grouts and protective treatments suited to the marble you chose. We have worked stone since 1956 and prefer to say it beforehand: joints done well cost less than joints redone.
Cleaning and regrouting a joint, step by step
- 01Work out if it is dirt or damageRun a fingernail along the joint: if it is only dark but compact, cleaning is enough. If it crumbles, is cracked or missing, it needs regrouting. If several joints are open or a tile sounds hollow, stop and call an installer.
- 02Clean with neutral detergent and a soft brushApply a slightly more concentrated pH-neutral stone detergent, wait a few minutes, brush along the joint with soft bristles, rinse with clean water and dry. No acids, no metal brushes.
- 03Remove the damaged groutWith a narrow grout scraper, work in the centre of the joint without touching the marble edges, which chip easily. Remove at least 2-3 mm of depth and vacuum the dust.
- 04Protect the edges and regroutOn light polished marbles first apply a protective treatment along the edges. Mix a little fine cement grout in the right colour, fill with a rubber float diagonally and remove the excess at once with a barely damp sponge.
- 05Clean the film and let it dryAfter a few hours wipe with a dry cloth to remove the cement film; if a haze remains, use the neutral detergent the next day. Do not wet the new joint for 24-48 hours.
- 06Protect and check over timeOnce the joint is dry, apply a water- and oil-repellent protective treatment on the joints too. If the crack reappears in the same place within a few months, the movement comes from the screed: an installer is needed.
Frequently asked questions
- How wide should the joints of a marble floor be?
- Normally 1-3 mm; 2 mm is the most used size for calibrated tiles. A near-zero joint looks good but releases every screed movement on the stone edges, which chip.
- What grout colour should I choose for white marble?
- A light grey or off-white similar to the stone background, not pure white nor the vein: the floor stays continuous and dirt shows less. Test on a spare tile.
- How do I clean the black joints of a marble floor?
- Slightly concentrated pH-neutral detergent, a few minutes of dwell time, a soft-bristle brush along the joint, rinse and dry. Never acids or limescale removers: they whiten the grout but dull the marble next to it.
- Why do the joints of my new floor crack?
- Usually because of screed shrinkage or missing expansion joints in large rooms. An isolated crack can be regrouted; many cracks in the same direction call for the installer.
- Can I use epoxy grout on polished marble?
- Only with experience and after protecting the edges: epoxy residue on light polished marble leaves a film that only re-polishing removes. For a home a fine cement grout is safer.
See also
