Marmi di Carrara, since 1956
Get a quote

Guides · Marmi di Carrara · 1956

Efflorescence and white marks on marble

Updated · By Marmi di Carrara srl

What it looks like

Efflorescence appears as a white powder, sometimes a thin crust, that seems to sit on top of the stone and often follows the joints or the edge of the tiles, where moisture escapes most easily. On white marble it shows as a dull, rough film, on dark marbles as chalky patches. The telltale sign: it comes off with a dry brush and reappears after a few weeks, in the same spot or next to it. It almost always shows on recently laid floors, terraces, outdoor stairs, pool surrounds and retaining walls, and increases in cold, damp months. It should not be confused with the limescale halo left by tap water, which is shiny and raised, nor with etching, which is inside the stone.

What causes it

Marble is calcium carbonate and slightly porous: water passes through it slowly. Screeds and bedding mortars contain soluble salts (mainly sulphates and alkaline carbonates from cement), which dissolve in the mixing water or in the moisture of the substrate. As the floor dries, water rises by capillarity through the stone and the joints, evaporates at the surface and leaves the salts as white crystals. The more water in the substrate, the more salts arrive: recently laid screeds, leaks from the terrace above, rain entering through outdoor joints, damp ground behind a wall. In some cases the salts crystallise just below the surface and, as they grow, can lift small flakes: this is the most damaging form.

What to do at once and what not to do

Remove the powder dry with a soft-bristle brush or a vacuum and collect it, rather than washing it: water re-dissolves the salts and sends them back into the stone. If a film remains, wipe with a barely damp cloth and clean water and dry at once. Repeat whenever it reappears, patiently: each brushing brings out some salt that will not return. Do not use acids, limescale removers or "cement cleaners": they dissolve the salts but etch the calcium carbonate and leave the marble dull. Do not seal a floor with active efflorescence: the protective treatment traps the salts below the surface and the problem gets worse. Do not cover a new floor with rugs or sheets; it must breathe to dry.

How to prevent it

Prevention happens before installation. The screed must be cured and dry (roughly one week per centimetre of thickness, and in any case checked with a moisture meter) before the marble is laid. Outdoors you need a barrier against rising damp and a slope that carries water away, with sealed joints and flashings. Mortars and adhesives for white marble should be low in salts and fast-setting, chosen with the installer. The water- and oil-repellent protective treatment is applied only on a dry, stabilised floor, usually after a few weeks, and must be breathable: a film-forming product closes the pores and turns salts into flakes. In a new floor, moderate ventilation and heating in the first months help the substrate dry evenly.

When to call us or a restorer

If after three or four months of brushing the efflorescence does not decrease, or if it appears on an old floor that was fine before, the substrate is receiving water from somewhere: a leak, a pipe, a terrace above. In that case you first need a technician to find the water, then a restorer. If the surface has flaked, become rough or dull, or if someone has already used an acid, the stone must be re-honed or re-polished on site by a professional. Our workshop in Carrara re-hones transportable pieces, cuts replacement pieces in the same material when a slab or some tiles are compromised and can advise the installer on mortars and protective treatments suited to our marble. We have worked stone since 1956 and prefer to tell you when it is worth waiting and when it is not.

Managing efflorescence, step by step

  1. 01Check that it really is efflorescenceRun a dry finger over it: if white powder comes off and the stone below is intact, it is salt. If the mark is shiny and raised it is limescale, if it is dull and inside the stone it is an etch: in those cases see the dedicated guides.
  2. 02Brush dry and collectUse a soft-bristle brush or a vacuum with a brush nozzle, working in one direction and collecting the powder. Do not wet it first: water re-dissolves the salts and sends them back into the stone.
  3. 03One barely damp pass, then dryIf a film remains, wipe with a microfibre cloth barely damp with clean water, no detergent, and dry at once with a dry cloth. Little water: the floor must dry, not get wet again.
  4. 04Let the substrate breatheIn new floors keep the rooms ventilated and moderately heated, with no rugs or sheets on top. With each passing week the screed gives up a little less moisture and salt.
  5. 05Repeat and note the datesRepeat the brushing every time the powder reappears and write down when it happens. If the intervals get longer, the phenomenon is fading. Only once the floor has been stable for some weeks apply a breathable protective treatment.
  6. 06If it continues, look for the waterIf after three or four months it does not improve, or it appears on an old floor, there is a leak to find. Call a technician and then, for the surface, us or a restorer. No acids in the meantime.

Frequently asked questions

Why does my new marble floor produce a white powder?
They are soluble salts from the screed and mortar that the installation moisture brings to the surface through the pores of the marble. It is normal in the first months: brush dry and let the substrate dry out.
Does efflorescence damage marble?
Usually not: the salts sit on top of the stone and can be removed. It becomes harmful if it crystallises below the surface and flakes it, or if someone treats it with acids that etch the calcium carbonate.
Can I wash efflorescence away with water and vinegar?
No. Vinegar is an acid and dulls marble, and excess water re-dissolves the salts and sends them back into the stone. Brush dry, at most a barely damp cloth with clean water.
How long does efflorescence last on a new floor?
It normally decreases within a few weeks and disappears within a few months as the screed dries. If after three or four months it does not improve, there is a water source to find.
Should I apply a sealer to stop efflorescence?
Not right away: on a still damp floor the protective treatment traps the salts below the surface and worsens the problem. Apply a breathable one only when the phenomenon is over and the floor is dry.

See also

Request a quote

WhatsApp