Marmi di Carrara, since 1956
Get a quote

Guides · Marmi di Carrara · 1956

Cracks and fissures in marble: natural or installation?

Updated · By Marmi di Carrara srl

What it looks like

Look at the line close up and under raking light. A natural vein has its own colour, grey, golden, crystalline white, follows a wavy path and often continues on the back or the edge of the slab with the same pattern; running a fingernail over it the surface is continuous and smooth. A healed fracture, also called a "hairline" or "open vein", can look like a crack but is full: it was closed by calcite or consolidated with resin in the workshop, and when wetted it holds no water. A real crack has sharp edges, a fingernail catches, a drop of water enters and darkens the line, and in thin pieces it shows on the opposite side too. If the crack starts from a corner of the sink cut-out, from an edge or from a spot where the tile sounds hollow, it is almost always a stress crack, not a flaw in the stone.

What causes it

Marble is calcium carbonate, a metamorphic rock that over millions of years has endured pressure and movement: veins and healed fractures are its history, not a defect, and at the quarry the more fractured slabs are backed with fibreglass mesh and resin precisely to make them safe. Real cracks come from stress. In floors: an uncured screed that shrinks, voids under the tile, slabs that flex, missing expansion joints. In countertops: internal corners of cut-outs cut to a sharp angle, which concentrate stress like a notch in a sheet; unsupported overhangs; cabinets out of level that make the slab work in bending; impacts from heavy pans; expansion of a sink fitted too tightly. Marble resists compression well but bending poorly: every crack tells where it was made to work badly.

What to do at once and what not to do

First establish whether it is natural or real with the fingernail and water test. If it is a vein or a healed fracture, do nothing: it is stable and only needs to be kept clean and protected like the rest. If it is a real crack, avoid loading that area, do not place weights on the overhang and keep water out: dry the line and, on a countertop, cover it temporarily with clear tape while waiting for repair. Do not fill the crack with silicone, instant glue or varnish: they yellow, stain the edges and make the proper repair harder. Do not try to "fix" a moving tile with grout or adhesive: the movement comes from the screed and the crack will return. Photograph the crack with a ruler next to it: it helps to see whether it grows.

How to prevent it

Installation cracks are prevented before installation: a dry, cured screed, a full bed of adhesive under every tile with no voids, expansion joints in large rooms and along walls. On countertops, sink and hob cut-outs must be cut in the workshop with rounded internal corners (radius of at least 5-10 mm) and, in 2 cm slabs, with reinforcement under the narrow bridges in front of and behind the sink. The cabinet must be level and the slab supported over its whole surface, with overhangs supported according to thickness. An inset sink needs a few millimetres of play. At home: do not stand on the top, do not put boiling pans near the cut-outs, do not use the edge of the top as a lever to open crates. Slabs with visible fractures should be chosen mesh-backed and in a suitable thickness: we say so before the order.

When to call us or a restorer

Every real crack should be seen by a professional: it is not a job to do at home. A restorer can clean the fissure, consolidate it with epoxy or polyester resins pigmented to the colour of the stone, then re-hone or re-polish the area, usually with a very discreet result on pieces that do not work in bending. If the crack crosses a thin bridge of a countertop, if the tile moves or if the crack grows over time, the repair will not hold and the piece should be replaced. Our workshop in Carrara cuts replacement pieces in the same material, with slabs in stock to match background and vein, re-cuts the holes with the correct radii and can advise the installer on how to prepare the substrate. We have worked marble since 1956 and, when a slab has a fracture, we say so beforehand: together we decide whether to mesh it, move the cut or change it.

Working out what kind of fissure it is, step by step

  1. 01Clean and look under raking lightWash with water and pH-neutral detergent, dry and look at the line with a low light from the side. Note whether it has its own colour, whether it waves like the other veins and whether it continues on the edge or the back.
  2. 02Fingernail testRun a fingernail across it. If the surface is continuous it is a vein or a healed fracture, and stable. If the fingernail goes in or catches along the whole line, it is an open crack.
  3. 03Water drop testPut a drop of water on the line and wait a minute. If it stays on the surface, the fissure is full. If it disappears inside and the line darkens, the crack is open and deep.
  4. 04Find the starting pointFollow the crack to where it begins: a corner of the sink cut-out, an edge, an overhang, a tile that sounds hollow. The starting point tells the cause and therefore the right repair.
  5. 05Photograph with a referenceTake a photo with a ruler or a coin next to it and note the date. Repeat after a few weeks: if the crack lengthens, there is ongoing movement and resin alone will not be enough.
  6. 06Call a professional with the photosSend the photos to us or to a restorer before touching the crack. A stable crack is consolidated with resin and re-polished; one that crosses a thin bridge or grows must be replaced in the same material.

Frequently asked questions

How do I tell whether a line in marble is a vein or a crack?
A vein has its own colour, is smooth under a fingernail and holds no water. A crack has sharp edges, a fingernail catches, and a drop of water enters and darkens the line.
My marble countertop cracked near the sink: why?
Almost always because of a cut-out corner cut to a sharp angle, a bridge too narrow without reinforcement or a cabinet out of level. Marble resists bending poorly: the crack starts where stress concentrates.
Can a crack in marble be repaired?
Yes, if it is stable: a restorer consolidates it with pigmented resin and re-polishes the area. If it crosses a thin bridge, if the piece moves or the crack grows, replacing the piece in the same material is the better choice.
What is the mesh on the back of marble slabs?
A fibreglass mesh bonded with resin in the workshop to make slabs with natural fractures or heavy veining safe. It is not a defect: it is normal practice on fine marbles and thin slabs.
The floor tiles all crack in the same direction: is it the marble?
No, it is the substrate: screed shrinkage, a flexing slab or missing expansion joints. An installer must check the screed; replacing only the tiles is not enough.

See also

Request a quote

WhatsApp