Guides · Marmi di Carrara · 1956
Scratches on marble: what can be done
Updated · By Marmi di Carrara srl
What it looks like
A scratch on marble is a line that changes how the surface reflects light: on polished marble it shows as a dull thread, on honed marble as a line lighter or shinier than the rest. The simplest way to classify it is to run a fingernail across it: if it glides without catching, it is a fine scratch limited to the polished skin; if it stops, the groove has entered the stone and it is a deep scratch. A web of thin circular marks, visible only against the light, is the normal wear of a used floor or top: not a defect but a finish that is changing. A white, powdery scratch with frayed edges indicates an impact, and often a small chip.
What causes it
Marble is calcium carbonate with Mohs hardness 3-4: a coin marks it, sand cuts it. Sand and grit carried in by shoes are quartz, hardness 7, and are the main cause of scratches on floors: every step drags them like sandpaper. On tops, the culprits are cast iron or steel pan bottoms, ceramics with an unglazed base, vases and objects dragged instead of lifted. Chair legs without felt pads dig circular grooves around tables. Wrong cleaning scratches too: abrasive sponges, scouring powders and even a cloth used with sand on it. Softness is not a flaw of marble, but it is the reason it is treated with different care from granite.
What to do at once and what not to do
First clean the area with water and pH-neutral detergent and dry it, so you see the scratch without dust around it. On honed marble a fine scratch can be softened by hand with a mild polishing paste for natural stone and a soft cloth, working in circular movements and checking often under raking light. Always test on a hidden spot. On polished marble it is better not to try: an abrasive paste used by hand removes the polish around and creates a dull patch more visible than the scratch. Do not use sandpaper, steel wool, toothpaste, baking soda or car polish. Do not fill the scratch with wax or clear varnish: they yellow and must then be removed. If a fingernail catches, no hand remedy will work.
How to prevent it
Against sand you need doormats: a rough one outside and one inside that holds dust, long enough for two or three steps. Sweep or vacuum the floor with a soft brush before washing, otherwise the mop drags the grains. Felt pads under every leg of chairs, tables and stools, checked and replaced when worn. In the kitchen, lift rather than drag pans, boards and small appliances; a board under ceramics with a rough base. In busy rooms, if the marble is new, consider a honed or brushed finish from the start: it hides signs of use far better than polished. A water- and oil-repellent protective treatment does not prevent scratches, but keeps the surface easier to clean.
When to call us or a restorer
If the scratch catches a fingernail, if it is on a polished surface or if a hand attempt has left a dull patch, it is time to stop. A restorer re-polishes on site with diamond pads of increasing grit: the surface is lowered by a few tenths of a millimetre, the scratch is removed and the original finish is restored over the whole area, not just on the mark. On a floor it is often worth re-honing the whole room for a uniform finish. Our workshop in Carrara re-polishes tops, tables and transportable pieces, cuts replacement pieces in the same material when a chip is too large and holds slabs in stock to match the colour. We have worked marble since 1956 and can say frankly when a scratch can be solved and when replacement is the better option.
Assessing and softening a scratch, step by step
- 01Clean and look under raking lightWash with water and pH-neutral detergent, dry and look at the scratch with a low light from the side, not from above: this shows its real length and whether there are finer marks around it.
- 02Do the fingernail testRun a fingernail across the scratch. If it glides, the scratch is superficial and you may try the next step only if the finish is honed. If it catches, go straight to the last step.
- 03Test in a hidden cornerOn honed marble, apply a mild polishing paste for natural stone on an area that is not seen, work with a soft cloth in small circles, dry and compare: the area must stay the same as the rest, not shinier.
- 04Work the scratch calmlyRepeat on the scratch, widening the movement beyond its edges so the transition stays invisible. Stop often, clean and check under raking light. A few minutes at a time, never strong pressure.
- 05Rinse, dry and protectRemove any residue with clean water, dry and, if the area was treated, reapply the water- and oil-repellent protective treatment following the product instructions.
- 06If it does not improve, call a professionalIf the scratch remains or the area has turned dull, do not insist with harsher products. Call us or a restorer: re-polishing with pads of increasing grit is the only remedy that restores the original finish.
Frequently asked questions
- Can scratches be removed from marble at home?
- Only fine scratches on a honed finish, with a mild polishing paste and a lot of patience. On polished marble and for scratches a fingernail catches, professional re-polishing with pads of increasing grit is needed.
- Why does my marble floor scratch so easily?
- Marble has Mohs hardness 3-4, sand under shoes is quartz with hardness 7: every step drags it like sandpaper. Long doormats and sweeping before washing greatly reduce the marks.
- Does toothpaste or baking soda remove scratches from marble?
- No. They are mild abrasives that dull the area around on polished marble and lack the right grit on honed marble: the scratch stays and a patch is added. A natural stone paste is better, and only on honed finishes.
- Can a deep scratch be repaired or must the piece be replaced?
- Almost always repaired: re-polishing lowers the surface by a few tenths of a millimetre and the scratch disappears. Replacement is needed with a large chip or a piece that is too thin; we cut the replacement in the same material.
- Which finish hides scratches best?
- Honed and brushed: they diffuse light and signs of use blend into the surface. Polished shows every thread against the light. For busy floors and lived-in kitchens it is a choice to make before installation.
See also
