Guides · Marmi di Carrara · 1956
Marble or porcelain stoneware for floors and bathrooms?
Updated · By Marmi di Carrara srl
Durability and strength: ceramic versus stone
Porcelain stoneware is a mix of clays and feldspars fired above 1200 °C: the result is a compact material with almost zero absorption and a very hard surface, harder than granite. Marble has a Mohs hardness of 3 to 4 and slight porosity: a marble floor wears a little in forced passages, such as in front of the entrance door, and sand under shoes can scratch it. It must be said, though, that porcelain is hard but brittle: a heavy object falling can chip it, and the chip shows the pale body under the print. Marble chips less easily and, if it happens, the chip is the same material and can be filled.
Care: cleaning and treatment
Porcelain is washed with water and any detergent and needs no treatment in its lifetime. Marble is washed with a pH-neutral cleaner and a microfibre cloth, avoiding limescale removers and acid products, and every one or two years the protective treatment is renewed, especially in a bathroom with soaps and cosmetics. In a bathroom marble also asks you to dry the basin top and not leave dripping bottles. It is not heavy work, but it is a discipline. Polished porcelain, on the other hand, shows every footprint and water mark; honed marble is more forgiving than people expect.
Heat and scratches: the practical differences
Both materials tolerate heat well: porcelain was born in a kiln and marble is a stone. In a bathroom heat is not an issue; on a floor with underfloor heating both work, and marble conducts warmth in a pleasant, even way. On scratches porcelain wins clearly, especially in matt finishes. On acids porcelain wins again: marble, faced with a limescale remover or an acidic cosmetic, develops a dull halo that shows immediately on a polished surface. That is why for marble bathrooms we recommend a honed finish and a regular protective treatment.
Value over time: the print and the stone
Marble-look porcelain is a photograph printed on ceramic: the pattern repeats every few faces, the vein does not continue through the thickness, and a cut or chipped edge reveals it. Over the years the print does not change, but it cannot be repaired either: a damaged tile is replaced, if the same batch can still be found. Marble is stone from one side to the other: the vein continues on edges and steps, every slab is a unique piece, and a worn floor is re-honed on site and comes back as new. In the value of a home a real Statuario bathroom remains recognisable and counts more than an imitation, however good.
Sustainability: an honest comparison
Porcelain requires firing above 1200 °C, which means a lot of energy per square metre, and it cannot be repaired. Marble is not fired: it is cut, honed and installed, it is a single material with no resins or glazes, it can be repaired and reused, and in the end it is still stone. The weight of marble lies in transport and quarrying, not in processing, which is why origin matters. Our white marbles come from our own quarries above Carrara and are worked in our own workshops a few kilometres away, with offcuts that remain stone. We do not say porcelain is wrong: we say the comparison must cover the whole life of the material.
When to choose one or the other
Choose porcelain for a high-traffic floor with sand and heels, for a service bathroom or a room where no one will do any maintenance, and when a large uniform format with no surprises is needed. Choose marble for the main bathroom, for shower walls, for an entrance or living room where the stone must be real and last generations, and when the project calls for continuous veins across floor, wall and basin. Our warehouse holds slabs in 2, 3 and 4 cm, polished or honed: for bathrooms usually 2 cm honed for cladding and tops, 3 cm for tops with a visible edge.
Frequently asked questions
- Can marble-look porcelain be told apart from real marble?
- Up close, yes: the print repeats, the vein does not continue on the edge and the touch is different. In a photo it can deceive; in a home, after a few years, the difference is seen and felt.
- Is marble suitable for a bathroom floor?
- Yes, it is one of its oldest uses. It needs a honed or otherwise non-slip finish, a protective treatment every one or two years and neutral cleaners. A marble shower asks you to dry it and avoid limescale removers.
- Can I see the real slabs before deciding?
- Yes. The slabs are in stock in Carrara and each lot has its photos online. You can visit the showroom or book a video call and look at them with us, slab by slab.
- Does marble work with underfloor heating?
- Yes, very well: stone conducts heat evenly and holds it. It needs correct installation with a suitable adhesive and expansion joints where the project requires them.
- What thickness is used for marble floors and cladding?
- Usually 2 cm for floors, walls and basin tops; 3 cm when the edge stays visible. Our warehouse holds slabs in 2, 3 and 4 cm, polished or honed; other finishes on request.
See also
- Marble or engineered quartz for the kitchen countertop? →
- Marble or granite for kitchen countertops and floors? →
- Marble or natural quartzite for kitchen and bathroom? →
- Marble in the kitchen: yes or no? →
- Marble countertop thickness: 2, 3 or 4 cm →
- Carrara marbles →
- Answers about Carrara marble →
- Marble glossary →
