Marmi di Carrara, since 1956
Get a quote

Guides · Marmi di Carrara · 1956

Marble and underfloor heating

Updated · By Marmi di Carrara srl

How to recognise it / what it is

Underfloor heating warms the room through a network of pipes or cables in the screed. The marble above becomes one large radiant surface: pleasant, silent, with no radiators. When something goes wrong, the signs are recognisable: a thin crack running across several slabs along a straight line, crumbling joints, a hollow sound in some areas, warmer and cooler zones that you feel barefoot, or a slight lifting near the walls. Almost always the fault does not come from the marble but from how the system was started up or how the laying was prepared. Understanding this first avoids blaming the stone.

What causes it

Marble is calcium carbonate with a density of about 2.7 t/m³, Mohs hardness 3-4, and it conducts heat better than wood or resins: that is why it warms up quickly and evenly, and because of its mass it gives heat back for a long time (thermal inertia). The screed, however, expands with temperature more than the stone and, if the temperature rises abruptly, stresses concentrate in the joints and at rigid points. A rigid adhesive does not absorb these movements and passes the stress on to the slab. Without movement joints along the perimeter and in large fields, the force has nowhere to go. Moisture in the screed evaporating quickly under heat can also lift slabs laid too early.

What to do / what NOT to do

Do: let the screed cure, then have the heating engineer run the test cycle (gradual heating up to working temperature, holding, then switching off) before laying; lay with the system off and cold; use a deformable cement-based adhesive, white for light marbles, in a full bed; allow perimeter and field joints; after laying wait for the adhesive and grout to cure fully, then restart raising a few degrees a day up to normal temperature. Do not: switch the system to maximum on the first cold day; cover the floor with thick insulating rugs over large areas for long periods without having planned for it; use rigid adhesives; fill perimeter joints with hard grout.

How to prevent it / how to design it well

Choose 2 cm slabs: they transmit heat quickly and have the right weight for a floor. Our workshop cuts them to size according to the laying plan, numbered for vein continuity. Prefer a honed finish if you often walk barefoot: honed marble is slightly warmer and softer to the touch than polished, which reflects more and shows marks more readily. Agree with the designer a moderate flow temperature and a control strategy that uses the mass of the marble. Plan the joints in the drawing, at doors and room changes, and choose an elastic sealant for the perimeter. Coordinate installer and heating engineer: the test cycle of the system and the laying date must be scheduled together.

When to call us or an installer/restorer

We supply the material cut to size and can discuss adhesive, thickness and joints with your installer, and the finish with the designer. If a heated floor already shows cracks running across several slabs, detached slabs or crumbling joints, it needs a site visit by an installer experienced in natural stone: the cause must be traced to the system, the screed or the joints. A broken slab can sometimes be replaced with a matching piece from our warehouse in Carrara, if the lot is still available; a marked surface can be re-polished. We cannot guarantee that a crack caused by the screed will not come back: in that case the problem must be solved at the base.

Laying over underfloor heating, step by step

  1. 01Let the screed cureThe screed holding the pipes must be cured and dry before any heating: for traditional cement screeds normally about 28 days. Heating engineer and installer must agree the date and measure residual moisture.
  2. 02Test cycle of the system before layingThe system is heated gradually up to working temperature, held for a few days and then switched off. This drives out moisture and lets the screed make its first movements before the stone is on top.
  3. 03Lay with the system off, deformable adhesiveLay on a cold floor. Deformable cement-based adhesive, white for light marbles, spread in a full bed on the screed and on the back of the 2 cm slab. Joints of at least 2-3 mm.
  4. 04Perimeter and field jointsLeave an elastic joint along all walls, at door thresholds and roughly every 20-25 m², or where the designer indicates. Joints are sealed with elastic material, never with rigid grout.
  5. 05Gradual restartAfter the adhesive and joints have fully cured, restart the system raising a few degrees a day up to normal temperature. The same applies at every start of the season: never sudden jumps.

Frequently asked questions

Is marble suitable for underfloor heating?
Yes, it is among the best materials: it conducts heat well, stores it and gives it back evenly. It only needs a correct installation, with deformable adhesive, joints and gradual start-up of the system.
Does marble crack with underfloor heating?
Not from the heat itself. Cracks come from sudden temperature jumps, uncured screeds or missing joints. With gradual start-up and correct laying the risk is low; a crack running across several slabs should be assessed by an installer.
What thickness should be used over underfloor heating?
Normally 2 cm: it transmits heat quickly and has the right weight for a floor. Greater thicknesses slow the response a little and add load without clear benefits.
Honed or polished on a heated floor?
Both work. Honed is slightly warmer and softer to the touch and hides small marks better; polished reflects more light and shows etching sooner. It is a matter of taste and use.
Can I put rugs on heated marble?
Yes, but thick insulating rugs over large areas trap heat underneath and create temperature differences. Better thin rugs, on limited areas, and if possible planned for in the design of the system.

See also

Request a quote

WhatsApp